Maytag 2015 Centennial top-load washer error codes (2024)

Maytag 2015 Centennial top-load washer error codes (1)

These error code explanations can help you diagnose a problem with your Maytag Centennial VMAX model top-load washer. For DIY repair how-to help, visit the PartsDirect repair help section, which includes repair help for washing machines, other major appliances, lawn and garden equipment, garage door openers, vacuum cleaners and more. Search for your model number to find a complete list of replacement parts for your washer.

Error Code

Condition

DIY advice

LF or F8 E1

Long fill

Check/Repair

Make sure that both water supply valves behind the washer are fully open. In winter, check the fill lines for freezing. Check the drain system for a siphon problem. If the water valve assembly is defective, replace it.

Possible parts

Water valve assembly

Sd or F0 E2

Excessive suds

Check/Repair

If you see excessive suds in the washer, start using the right amount of high-efficiency (HE) detergent.

Possible parts

(HE) detergent

F0 E3

Overload

Check/Repair

The size of the load exceeds the washer's capacity. Open the lid and remove some garments. Restart the cycle.

Possible parts

F0 E4

Spin limited by water, temperature,

Check/Repair

This code displays when the water temperature is too high during the final spin. Spin speed is limited to 500 rpm when this code appears. Check the water valve functions using the diagnostic test mode. Replace the water valve assembly if the hot water valve sticks open.

Possible parts

Water valve assembly

F0 E5

Unbalanced load

Check/Repair

Distribute items evenly when loading. Level the washer cabinet. Check for weak suspension springs. With the washer empty, open the lid and push down firmly on the basket. The basket should not bounce up and down more than once when pushed. Replace the suspension springs if defective.

Possible parts

Suspension springs

F1 E1

Main electronic control board failure

Check/Repair

Try to reset the control board by unplugging the washer for 5 minutes and then restoring power. If the F1E1 code returns after restoring power, replace the main electronic control board.

Possible parts

Main electronic control board

F1 E2

Main electronic control board failure

Check/Repair

This code signals a failure in the motor control circuit of the main electronic control board. Unplug the washer and check the main electronic control board wiring. Check the drive motor wiring. Reconnect any loose wires. Open the lid and spin the impeller inside the basket. The impeller should rotate freely. Remove the restriction in the drive system if the impeller doesn't spin freely. If the basket spins freely, replace the main electronic control board.

Possible parts

Main electronic control board

F1 E3

Mismatch of the main electronic control board and the user interface control

Check/Repair

The code appears when you install the wrong user interface control. Order and install the correct user interface control for your model of washer.

Possible parts

User interface control

F2 E1

Stuck button

Check/Repair

Attempt to release the stuck button. If you cannot release the stuck button, replace the user interface control.

Possible parts

User interface control

F2 E3

User interface control or main electronic control board mismatched

Check/Repair

The code appears when you install the wrong user interface control or main electronic control board. Order and install the correct user interface control or main electronic control board for your model of washer.

Possible parts

User interface control board, main electronic control board

F2 E4

User interface control error

Check/Repair

Unplug the washer. Open the console and check the wire harness connection between the main electronic control board and the user interface control. If the wire harness connection is okay, replace the user interface control.

Possible parts

User Interface control

F2 E5

User interface failure

Check/Repair

Unplug the washer and replace the user interface control.

Possible parts

User interface control

F3 E1

Water level signal out of range

Check/Repair

Check the water level pressure tube for kinks, blockages or air leaks. Replace the water level pressure tube if damaged. The water level detector is a component of the main electronic control board. If the water level pressure tube is okay, replace the main electronic control board.

Possible parts

Water level pressure tube, main electronic control board

F3 E2

Water temperature sensor failure

Check/Repair

The water temperature sensor is a component on the water valve assembly. Unplug the washer and check the wire harness connection between the main electronic control board and the water valve assembly. Reconnect any loose wires. Replace the wire harness if damaged. If the wiring is okay, replace the water valve assembly.

Possible parts

Water valve assembly

F5 E1

Lid switch error

Check/Repair

This code displays when the lid switch detects an open lid with the lid locked. Unplug the washer and check the wire harness connections on the lid lock/switch. If the wiring connections are okay, replace the lid lock/switch.

Possible parts

Lid lock/switch

F5 E2

Lid won't lock

Check/Repair

Check for debris in the lid lock mechanism that could prevent it from locking. Unplug the washer and check the wire harness connections for the lid lock/switch on the main electronic control board. Examine the lid lock/switch assembly. If it's damaged or defective, replace it.

Possible parts

Lid lock/switch

F5 E3

Lid won't unlock

Check/Repair

Unplug the washer. Check the wire harness connections for the lid lock/switch assembly on the main electronic control board. If the connections are okay, then you will typically need to force the lid open. This will usually break the lid lock/switch. Replace the lid lock/switch if it's damaged or broken.

Possible parts

Lid lock/switch

F5 E4

Lid not opened, between loads,

Check/Repair

The main electronic control board doesn't detect the lid opening between loads. Unplug the washer and check the wiring connections between the lid lock/switch and the main electronic control board. If the wiring connections are okay, replace the lid lock/switch.

Possible parts

Lid lock/switch

F6 E2 or F6 E3

Communication error

Check/Repair

This code signals a communication failure between the user interface control and the main electronic control board. Unplug the washer and check the wire harness between the user interface control and the main electronic control board. Reconnect any loose wires. Replace the wire harness if damaged. Replace the user interface control. If the problem persists, replace the main electronic control board.

Possible parts

User interface, main electronic control board,, wire harness,

F7 E0

Loss of electrical power

Check/Repair

Plug in the power cord securely. Replace the power cord if damaged. Unplug the washer and check the power cord wiring connections on the main electronic control board. Reconnect any loose wires. Have an electrician check voltage at the electrical outlet.

Possible parts

Power cord

F7 E1

Loss of power during, spin mode,

Check/Repair

This fault code displays when power is lost during the spin mode. The washer pauses for 5 minutes to allow the spin basket to stop before continuing the cycle. Plug in the power cord securely. Replace the power cord if damaged. Unplug the washer and check the power cord wiring connections on the main electronic control board. Reconnect any loose wires. Have an electrician check voltage at the electrical outlet.

Possible parts

Power cord

F7 E2

Drive motor failure

Check/Repair

Unplug the washer and check the wire harness connections between the drive motor and the main electronic control board. Reconnect any loose wires. Replace the wire harness if damaged. Open the lid and spin the impeller inside the basket. The impeller should rotate freely. Remove the restriction in the drive system if the impeller doesn't spin freely. If the basket spins freely, replace the drive motor. If the problem persists, replace the main electronic control board

Possible parts

Drive motor, wire harness, main electronic control board

F7 E3

The clutch engaged the spin basket during the wash cycle

Check/Repair

The clutch should only engage the spin basket during the spin cycle. Unplug the washer and check the clutch for obstructions. Remove any obstructions and replace the clutch if damaged.

Possible parts

Clutch

F7 E4 and F7 E5

Clutch failure

Check/Repair

The clutch failed to engage the spin basket in the spin mode. Unplug the washer and check the clutch for obstructions. Remove any obstructions. Replace the clutch if damaged. Check the wiring connections between the clutch and the main electronic control board. Reconnect any loose wires. Replace the wire harness if damaged. If the wiring connections are okay, replace the clutch.

Possible parts

Clutch, wire harness

F7 E6

Drive motor circuit failure

Check/Repair

Unplug the washer and check the wire harness connections between the drive motor and the main electronic control board. Reconnect any loose wires. Replace the wire harness if damaged. If the wire harness is okay, replace the drive motor.

Possible parts

Drive motor, wire harness

F7 E7

Motor not able to reach target rpm

Check/Repair

Mechanical friction in the drive system caused by items stuck between the spin basket and tub prevents the motor from reaching the target rpm. Remove any obstructions between the spin basket and tub. An unbalanced load can also cause the F7E7 error code. Distribute items evenly when loading. Level the washer cabinet. Check for weak suspension springs. With the washer empty, open the lid and push down firmly on the basket. The basket should not bounce up and down more than once when pushed. Replace the suspension springs if defective. Unplug the washer and check the wire harness connections between the drive motor and the main electronic control board. Reconnect any loose wires. Replace the wire harness if damaged. If the wire harness is okay, replace the drive motor.

Possible parts

Drive motor, suspension springs

F7 E8

Overheated motor

Check/Repair

Mechanical friction in the drive system caused by items stuck between the spin basket and tub can overheat the motor. Remove any obstructions between the spin basket and tub. The water level and load size detection systems may need calibrating if water level is too low for the selected cycle. Run the Service Calibration in the Service Test Mode to calibrate water level to washer cycles. A defective drive motor will overheat. Replace the drive motor if defective.

Possible parts

Drive motor

F7 E9

Locked rotor

Check/Repair

The motor doesn't move when activated. Check for mechanical friction in the drive system caused by items stuck between the spin basket and tub. Remove any obstructions between the basket and tub. If there are no obstructions, replace the drive motor.

Possible parts

Drive motor

F8 E3

Overflow or flood condition

Check/Repair

The electronic control senses a water level that exceeds washer capacity. Check the water level pressure tube for kinks, blockages or air leaks. Replace the water level pressure tube if damaged. Check to see if water siphons out through the drain hose. Install the washer drain system according to installation manual guidelines to prevent siphoning of fill water. A leaking water valve can cause the F8E3 code. Unplug the washer and see if the tub fills with water. If so, replace the water valve assembly.

Possible parts

Water level pressure tube, water valve assembly

F8 E6

Water hazard

Check/Repair

This fault code displays when the main electronic control board senses water in the tub with the lid open for more than 10 minutes. A leaking water inlet valve fills the tub when the washer is off. Replace the water inlet valve if leaking.

Possible parts

Water inlet valve

F9 E1, F9 E2, drn or dr

Long drain time

Check/Repair

This code is displayed when the water level does not change after the drain pump runs. If the washer does not drain, check the drain hose and washer drain for a clog or restriction. Unplug the washer and check the drain pump for a clog. If the drain pump is defective, replace it. If the washer is draining correctly and the drop in water level isn't being detected, replace the main electronic control board.

Possible parts

Drain pump, main electronic control board

Maytag 2015 Centennial top-load washer error codes (2024)

References

Top Articles
Latest Posts
Article information

Author: Annamae Dooley

Last Updated:

Views: 6384

Rating: 4.4 / 5 (65 voted)

Reviews: 88% of readers found this page helpful

Author information

Name: Annamae Dooley

Birthday: 2001-07-26

Address: 9687 Tambra Meadow, Bradleyhaven, TN 53219

Phone: +9316045904039

Job: Future Coordinator

Hobby: Archery, Couponing, Poi, Kite flying, Knitting, Rappelling, Baseball

Introduction: My name is Annamae Dooley, I am a witty, quaint, lovely, clever, rich, sparkling, powerful person who loves writing and wants to share my knowledge and understanding with you.